Simplex – Fire & Safety WA

IDNet Relay IAM with Unsupervised Input (Uses RACO232 & Lid)

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

The 4090-9119 allows a 4100ES IDNet communication channel to monitor an unsupervised input contact with one point and control an output relay with the other point, yet occupy a single address. The input circuit and relay operation are controlled independently and may be disabled separately. Module power is supplied from the IDNet communications channel eliminating the need for separate power wiring. The address is set by DIP switch under the re-sealable label.

Specifications
– Comms Power 24 to 40Vdc w/data*
– Relay Contact Ratings SPDT
Non power limited 0.5A @120VAC**
0.25A@120VAC***
Power limited 2A@30Vdc**
1A@30Vdc***
– Input N/O, dry contacts
– Dimensions (HWD) 105 x 105 x 35 mm
– Ambient Temperature 0 to +49°C
– Relative Humidity 10% to 95% (n/c)

* IDNet communications with data
** Resistive Load
*** Inductive Load
Note: Loop powered 2 wire device

IDNet 6 Point I/O Module (4 I/Ps + 2 relay O/Ps) (Uses RACO232 & Lid)

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

The 4090-9120 allows 4100ES IDNet communication channel to monitor four T-sense input circuits and control two output relays from a single module requiring a single address. Power is supplied by a separate 24Vdc connection to a listed fire alarm power supply. The input circuits and output relay operation are controlled independently and may be disabled separately. Point association is determined at the 4100ES host panel. At the 4100ES, the device address is designated as a single hardware location. Each of the four input circuits monitors for continuity to an end-of-line resistor and can differentiate between a short circuit contact closure and a current limited contact closure. Two input supervision resistors are required per T-sense input.

Specifications
– Comms Power 24 to 40Vdc w/data*
– Operating Voltage 18 to 32Vdc
– Operating Current 30mA@24Vdc
– Relay Contact Ratings SPDT
Non-power limited 0.5A @120VA**
0.25A@120VAC***
– Power limited 2A@30Vdc**
1A@30Vdc***
– Supervision Resistor 6k8 Ohm 0.5W
– Current Limited Operation 1k8/4k7 0.5W
– Input N/O, dry contacts
– LED Output 24Vdc (external PSU)
– Dimensions (HWD) 105 x 105 x 35 mm
– Ambient Temperature 0 to +49°C
– Relative Humidity 10% to 90% (n/c)

* IDNet communications with data
** Resistive Load
*** Inductive Load
Note: 4 wire device; requires separate 24Vdc and IDNet communication loop

Addressable MCP Mounting Box

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

Red surface mounting back box (for indoor callpoints) with terminals fitted.

SIMPLEX Remote LED Mapnet `Roof Space’

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

The 2098-1xxx range of remote indicators provide remote indication of an alarm condition on a detector fixed on a 4098-97xx detector base. These remote indicators are not suitable for connection to any other MAPNET II or IDNet module. They are used where the fire detector is installed in an inaccessible location, and indication of alarm must be provided in an easily accessible area. For example, where the detectors are in roof spaces or cupboards, under the floor, or in hotel rooms, and indication is required in the room or corridor.

Specifications
– Operating Voltage 1.8Vdc Typ.
(from 4098-97xx Base)
– Alarm Current (min.) 1.6mA
– Alarm Current (max.) 25mA@45°C
15mA@75°C
– Luminous Intensity as per AS2362.25
– Relative Humidity 10% to 95% (n/cond)
– Ambient Temperature -5°C to +75°C

SIMPLEX Remote LED Mapnet `Concealed Space’

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

SIMPLEX Remote LED Mapnet `Cupboard’

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

TrueAlarm Base with Remote LED O/P

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

TrueAlarm detector bases contain integral addressable electronics that constantly monitor the status of the detachable photoelectric, ionisation, or heat detectors. Each detector’s output is digitised and transmitted to the system CIE every four seconds. Since TrueAlarm detectors use the same base, different detector types can be easily interchanged to meet specific location requirements, for example, during building construction, or when conditions are temporarily dusty. Instead of covering the smoke detectors(causing them to be disabled), heat detectors may be installed without reprogramming the CIE. Although the CIE will indicate an incorrect detector type, the heat detector will operate at a default sensitivity maintaining building protection at that location.

The 4098-9789EAP can be used in areas that may experience an increased moisture level, eg under eaves

Specifications
– Operating Voltage 24 to 40Vdc*
– Quiescent Current (max) 400µA
– Alarm Current (max) 3.2mA
– Relative Humidity 10% to 95% (n/cond)
– Ambient Temperature 0 to +55°C
– ActivFire Listed afp-1225 & 1246

* MAPNET II or IDNet auto select

SIMPLEX Remote LED Mapnet `Room’

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

TrueAlarm Base with Sounder

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

The 4098-9714EA Photoelectric smoke detector contains a state-of-the-art sensing chamber and analogue communication electronics. Used in conjunction with the Simplex 4100 panel, the 9714E has a high degree of false alarm immunity thanks to advanced algorithms. The detector mounts on the 4098-9789 addressable base or 4098-9794 sounder base. An optional remote LED can also be fitted.

Specifications
– Operating Voltage 24 to 40Vdc*
– Quiescent Current (max) 100µA
– Alarm Current-relay active 24mA
– External Output Drive (max) 5mA
– Relative Humidity 10% to 95% (n/cond)
– Ambient Temperature -9°C to +50°C
– Air Velocity 0 to 610m/min
– Sensitivity 4 to 6% Obs/m
– ActivFire Listed afp-1225

* MAPNET II or IDNet auto select w/data

SIMPLEX Remote LED Mapnet `Return Air’

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000