Detector – Fire & Safety WA

TrueAlarm Base with Remote LED O/P

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

TrueAlarm detector bases contain integral addressable electronics that constantly monitor the status of the detachable photoelectric, ionisation, or heat detectors. Each detector’s output is digitised and transmitted to the system CIE every four seconds. Since TrueAlarm detectors use the same base, different detector types can be easily interchanged to meet specific location requirements, for example, during building construction, or when conditions are temporarily dusty. Instead of covering the smoke detectors(causing them to be disabled), heat detectors may be installed without reprogramming the CIE. Although the CIE will indicate an incorrect detector type, the heat detector will operate at a default sensitivity maintaining building protection at that location.

The 4098-9789EAP can be used in areas that may experience an increased moisture level, eg under eaves

Specifications
– Operating Voltage 24 to 40Vdc*
– Quiescent Current (max) 400µA
– Alarm Current (max) 3.2mA
– Relative Humidity 10% to 95% (n/cond)
– Ambient Temperature 0 to +55°C
– ActivFire Listed afp-1225 & 1246

* MAPNET II or IDNet auto select

TrueAlarm Base with Sounder

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

The 4098-9714EA Photoelectric smoke detector contains a state-of-the-art sensing chamber and analogue communication electronics. Used in conjunction with the Simplex 4100 panel, the 9714E has a high degree of false alarm immunity thanks to advanced algorithms. The detector mounts on the 4098-9789 addressable base or 4098-9794 sounder base. An optional remote LED can also be fitted.

Specifications
– Operating Voltage 24 to 40Vdc*
– Quiescent Current (max) 100µA
– Alarm Current-relay active 24mA
– External Output Drive (max) 5mA
– Relative Humidity 10% to 95% (n/cond)
– Ambient Temperature -9°C to +50°C
– Air Velocity 0 to 610m/min
– Sensitivity 4 to 6% Obs/m
– ActivFire Listed afp-1225

* MAPNET II or IDNet auto select w/data

TrueAlarm IDNET Isolator Base

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

The 4098-9793 isolator base accepts Simplex TrueAlarm analog sensors and provides communications isolation to improve installation convenience and increase system integrity. An internal isolation relay allows a compatible c.i.e. to separate shorted communications wiring from functioning wiring to optimise the available sensors or other IDNet addressable devices. The isolator base’s status is communicated to the FIP, allowing it to assist in identifying the location of the shorted wiring. During installation, earth faults frequently occur. Finding these faults normally requires extensive wiring disconnection. With the 4098-9793 isolator base, earth faults on the IDNet communications lines can be quickly located to assist in their repair and to restore the system wiring
to normal.

Specifications
– Operating Voltage 24 to 40Vdc*
– Input Voltage 18.9 to 32Vdc
– Current (max.@ 24Vdc) 500µA
– Supervisory Resistor (9101) 3k3 Ohm 1W
– Dimensions (HWD) 105 x 105 x 35mm
– Relative Humidity 10% to 95% (n/cond)
– Ambient Temperature -9°C to +50°C

* IDNet, 1 address per base

Housing Without Relay (includes photo sensor)

AJBPIKE — Sun, 07 Oct 2018 13:31:41 +0000

The TrueAlarm duct sampling unit detects the presence of smoke in air conditioning or ventilating ducts. Sampling tubes are installed into the duct and air is directed to a 4098-9714EA smoke sensor mounted in the housing. These duct housings provide the high reliability performance of TrueAlarm analog sensing featuring programmable sensitivity, consistent accuracy, environmental compensation, status testing, and monitoring of sensor dirt accumulation. The TrueAlarm Duct Sampling Unit require only two
wires for both communications and power.

Specifications
– Operating Voltage 18 to 40Vdc*
– LED Current 600µA**
– Air Velocity 1.5 to 20 m/s
– Relative Humidity 10% to 95% (n/cond)
– Operating Temperature 0 to +50°C
4098-9753 with auxiliary relay
– Relay Coil Voltage 18 to 32Vdc
– Quiescent Current 240µA @ 24Vdc
– Alarm Current 32mA @ 24Vdc
– Contact Rating 1A @ 28Vdc (pwr limit)
-Contact Rating 0.5A @ 120VAC (resist)
– ActivFire Listed afp-1354

* MAPNET II
** No impact on alarm current

Adapter between S100 and XM69 Changer